IDoc Inbound is a test that will inject the message to the SAP backend. It can also perform validation of the database entries created by the message processing in the backend ABAP based system once the IDoc was posted successfully.
Top of the screen with Automation Object (AO) ID, description and test type.
Basic Information
Parameter name | Description | Example |
IDoc Type | IDoc Message Type, Basic Type and Extension. All Separated by a “.”. | ORDERS.ORDERS05 |
|---|
Backend Systems
Parameter name | Description | Example |
Backend system line for current doc. | This parameter points out the system where the reference backend document is stored. The value should be a system line described in the landscape configuration. Note: If Backend system line for the current doc. has the same value as the Backend system line for the reference doc. (for instance, both are S4/HANA) then the RFC connection between the systems will be maintained both in: a) the original environment of the reference document (for instance, production system) b) the environment where the current test case execution takes place (for instance, development system) If Backend system line for the current doc. is different than the Backend system line for the reference doc. then, the RFC connection will be maintained only in the environment of the current execution (for instance, development system), but for both system lines (like ECC and S4HANA) | ECC SAP_ERP |
|---|---|---|
Backend system line for reference doc. | This parameter points out the system line where Int4 Suite should create test documents during test case execution. In most cases, reference documents and documents created during current test execution are stored in the same system line. However, suppose Int4 Suite is used in a migration scenario (for example, migration from ECC to S4/HANA). In that case, the documents might be created in the new system and then compared with the references from the old system. The value should be a system line described in the landscape configuration. Note: If Backend system line for the current doc. has the same value as the Backend system line for the reference doc. (for instance, both are S4/HANA) then the RFC connection between the systems will be maintained both in: a) the original environment of the reference document (for instance, production system) b) the environment where the current test case execution takes place (for instance, development system) If Backend system line for the current doc. is different than the Backend system line for the reference doc. then, the RFC connection will be maintained only in the environment of the current execution (for instance, development system), but for both system lines (like ECC and S4HANA) | S4HANA |
Database Validations
Parameter name | Description | Example |
Database validation ruleset | Reference database validation ruleset object name. Database validation ruleset specify how related backend validation should be performed. Specify tables, fields and join conditions for the backend validation. Buttons allow navigation to the chosen database validation ruleset and creation of a new database validation ruleset | GENERIC_SO |
|---|
Variables
Variables are the container for values that can be used during testing. Each variable contains two values, the one that is calculated based on the reference message/document and the one that is calculated ad-hoc during test case execution.
Link to be added
Create button allows variable creation.
Parameter name | Description | Example |
Name | Variable technical name | VARIABLE_1 |
|---|---|---|
Description | Free text for variable description | Variable One |
Type | Type of variable processing | Read & Replace Find message Custom |
Scope | Scope determines the processing of procedures that generate unique values like, e.g., GUID or NUM_RANGE.
| Test Case Test Run |
IDoc Status Validations
IDOC Status Validation parameters are used to override default status handling rules for Inbound and Outbound IDOC test types.
Default status handling is based on system settings configured in tables STACUST & STALIGHT:
Read Status Group (STATVA) from STACUST
Read Status traffic light (STALIGHT) from STALIGHT
STALIGHT | Int4 Suite Test Result |
|---|---|
1 - Yellow | Waiting for IDOC to be processed. If maximum number of attempts exceeded Test is marked as Failed |
2 - Green | Test marked as Failed |
3 - Red | Test marked as Passed |
Individual statuses can be specified in Automation Object rules to override the above logic.
Parameter name | Description | Example |
IDoc Status | IDoc Status | 53 |
|---|---|---|
Rule | Describes behaviour of Int4 Suite for IDoc status | Success - Mark as Passed |
Execution Settings
Parameter name | Description | Example |
Debug Log | Int4 Suite will provide additional, more technical information in Test Execution Report during the running of the test cases if this parameter is set. Therefore, it is recommended to set this option initially and deactivate it when object definition is confirmed after executing the first test cases | |
|---|---|---|
Display wait popup before validation | Wait Flag indicating if Int4 Suite should stop test case execution after sending test case message to middleware. Int4 Suite will show the confirmation box, and the user will decide to continue. This setting can execute manual follow-up actions before running the next test case or checking the validations. This setup works only with Execute via SAP GUI option of execution |
Delay between execution and validation
Parameter name | Description | Example |
For each test case | Delay (in seconds) between test case execution ( sending message) and checking the results. | 10 |
|---|---|---|
Once per test run | Delay (in seconds) between test run execution ( sending messages) and checking the results. | 60 |
Number Ranges
The number ranges allow generating new values for variables. Those values are used to substitute original document numbers or other values in reference messages.
The number range used to replace the source system document number should always be configured to not overwrite the original number. It means that documents generated by Int4 Suite should have their own subset of the original document number. Usually, it might be a subset of the upper limit of the original number range.
It is essential that automated testing with Int4 Suite consume numbers that the source system will generate during manual testing. Additionally, if testing environment data is refreshed from the production system, more documents would be created in the testing environment. If the Int4 Suite number were configured in the same range, it would start creating duplicates.
For example, the original number range for document numbers from the source system is 560000 - 590000. It would be wise to set the Int4 Suite number range from 590000 to 600000. However, suppose the SAP backend system uses an external number range. It is essential to stay in the original range. In that case, the Int4 Suite number range may be set as 585000-590000, which gives space for 5000 testing documents. Using range from upper interval reduces the risk that the number will be overwritten.
Additionally, the good practice is to use prefixes or suffixes that will quickly separate source system documents and the ones created by Int4 Suite. It should always be used when there is no document number validation by the SAP backend.
Each Object Definition can contain an unlimited number of number ranges. This way, each variable declared in an object can use its specific number range.
Parameter name | Description | Example |
Number range | Provide a name for the number range. This name would be passed as a parameter in variable processing for actions that will generate values from it. | NUM_RAN |
|---|---|---|
Prefix | The alphanumeric characters to be appended at the beginning of the document number to separate original documents from source systems and the one created during Int4 Suite testing (optional). | INT4_ |
Low value | The first number of our range. | 1 |
High value | The last number of our range. | 999999 |
Current value | When the number range is used during testing, it would increment per each use. | 23 |
Suffix | The alphanumeric characters to be appended at the end of the document number to separate original documents from source systems and the one created during Int4 Suite testing (optional). | _TEST |
Add zeros | If this box is checked, zeros will be automatically appended to the beginning of the document number, such as 000500. | |
Incr. per Test Run | If this indicator is selected, the number range is incrementing once per test run. If multiple test cases with the same Automation Object exist in the test run, they will receive the same value. |